Items

Advanced search

Hygroscopic behavior of NaCl–MgCl2 mixture particles as nascent sea-spray aerosol surrogates and observation of efflorescence during humidification

As Na+, Mg2+, and Cl− are major ionic constituents of seawater, NaCl–MgCl2 mixture particles might represent sea-spray aerosols (SSAs) better than pure NaCl. However, there have been very few hygroscopic studies of pure MgCl2 and NaCl–MgCl2 mixture aerosol particles despite the MgCl2 moiety playing a major role in the hygroscopic behavior of nascent SSAs. Laboratory-generated pure MgCl2 and NaCl–MgCl2 mixture aerosol particles with 12 mixing ratios (0.01 ≤ mole fraction of NaCl (XNaCl) ≤ 0.9) were examined systematically by optical microscopy (OM), in situ Raman micro-spectrometry (RMS), and scanning electron microscopy/energy dispersive X-ray spectrometry (SEM/EDX) elemental X-ray mapping to observe their hygroscopic behavior, derive the experimental phase diagrams, and obtain the chemical micro-structures. Dry-deposited MgCl2 ⋅ 6H2O particles exhibited a deliquescence relative humidity (DRH) of ~ 33.0 % and an efflorescence RH (ERH) of 10.8–9.1 %, whereas the nebulized pure MgCl2 and MgCl2-dominant particles of XNaCl = 0.026 (eutonic) and 0.01 showed single-stage transitions at DRH of ~ 15.9 % and ERH of 10.1–3.2 %. The characteristic OH-stretching Raman signatures indicated the crystallization of MgCl2 ⋅ 4H2O at low relative humidities (RHs), suggesting that the kinetic barrier to MgCl2 ⋅ 6H2O crystallization is not overcome in the timescale of the dehydration measurements. The NaCl–MgCl2 mixture particles of 0.05 ≤ XNaCl ≤ 0.9 generally showed two-stage deliquescence: first at the mutual DRH (MDRH) of ~ 15.9 %; and second with the complete dissolution of NaCl at the second DRHs depending on the mixing ratios, resulting in a phase diagram composed of three distinct phases. During dehydration, most particles of 0.05 ≤ XNaCl ≤ 0.9 exhibited two-stage efflorescence: first, by the homogeneous nucleation of NaCl; and second, at mutual ERH (MERH) of ~ 10.4–2.9 %, by the crystallization of the MgCl2 ⋅ 4H2O moiety, also resulting in three distinct phases. Interestingly, particles of XNaCl = 0.1 and 0.2 frequently showed three different types of mutual deliquescence behaviors. The first type exhibited an MDRH at ~ 15.9 %. The second exhibited the first MDRH at ~ 15.9 %, efflorescence to MgCl2 ⋅ 6H2O (confirmed by in situ RMS) at RH of ~ 16.1–25.0 %, and a second MDRH at ~ 33.0 %. The third showed an MDRH at ~ 33.0 %. Some particles of XNaCl = 0.1 and 0.2 also exhibited higher MERHs = 15.2–11.9 % and 23.7–15.3 %, respectively, forming MgCl2 ⋅ 6H2O. These observations suggest that the presence of sufficient condensed water and optimally sized crystalline NaCl (XNaCl = 0.1 and 0.2) acting as heterogeneous nucleation seeds helps overcome the kinetic barrier, leading to the structural growth and crystallization of MgCl2 ⋅ 6H2O. SEM/EDX elemental X-ray mapping showed that the effloresced NaCl-rich particles contain homogeneously crystallized NaCl in the center, surrounded by MgCl2 ⋅ 4H2O. The observation of an aqueous phase over a wider RH range for NaCl–MgCl2 mixture particles indicates their more probable heterogeneous chemistry compared to pure NaCl particles as a nascent SSA surrogate.
Organic aerosol evolution and transport observed at Mt. Cimone (2165 m a.s.l.), Italy, during the PEGASOS campaign

High-resolution aerosol mass spectrometer measurements were performed, for the first time, at the Mt. Cimone Global Atmosphere Watch (GAW) station between June and July 2012, within the EU project PEGASOS and the ARPA–Emilia-Romagna project SUPERSITO. Submicron aerosol was dominated by organics (63 %), with sulfate, ammonium and nitrate contributing the remaining 20, 9 and 7 %, respectively. Organic aerosol (OA) was in general highly oxygenated, consistent with the remote character of the site; our observations suggest that oxidation and secondary organic aerosol (SOA) formation processes occurred during aerosol transport to high altitudes. All of the aerosol component concentrations as well as the OA elemental ratios showed a clear daily trend, driven by the evolution of the planetary boundary layer (PBL) and by the mountain wind regime. Higher loadings and lower OA oxidation levels were observed during the day, when the site was within the PBL, and therefore affected by relatively fresh aerosol transported from lower altitudes. Conversely, lower loadings and higher OA oxidation levels were observed at night, when the top of Mt. Cimone resided in the free troposphere although affected by the transport of residual layers on several days of the campaign. Analysis of the elemental ratios in a Van Krevelen space shows that OA oxidation follows a slope comprised between −0.5 and −1, consistent with addition of carboxylic groups, with or without fragmentation of the parent molecules. The increase of carboxylic groups during OA ageing is confirmed by the increased contribution of organic fragments containing more than one oxygen atom in the free troposphere night-time mass spectra. Finally, positive matrix factorization was able to deconvolve the contributions of relatively fresh OA (OOAa) originating from the PBL, more aged OA (OOAb) present at high altitudes during periods of atmospheric stagnation, and very aged aerosols (OOAc) transported over long distances in the free troposphere.
Investigating the discrepancy between wet-suspension- and dry-dispersion-derived ice nucleation efficiency of mineral particles

Cloud chamber investigations into ice nucleation by mineral particles were compared with results from cold-stage droplet freezing experiments. Kaolinite, NX-illite, and K-feldspar were examined, and K-feldspar was revealed to be the most ice-active mineral particle sample, in agreement with recent cold-stage studies. The ice nucleation efficiencies, as quantified using the ice-active surface site density method, were found to be in agreement with previous studies for the lower temperatures; however, at higher temperatures the efficiency was between a factor of 10 and 1000 higher than those inferred from cold-stage experiments. Numerical process modelling of cloud formation during the experiments, using the cold-stage-derived parameterisations to initiate the ice phase, revealed the cold-stage-derived parameterisations to consistently underpredict the number of ice crystals relative to that observed. We suggest the reason for the underestimation of ice in the model is that the slope of the cold-stage-derived ice-active surface site density vs. temperature curves are too steep, which results in an underestimation of the number of ice crystals at higher temperatures during the expansion. These ice crystals suppress further freezing due to the Bergeron–Findeison process. A coagulation model was used to investigate the idea that the mineral particles coagulate in suspension. This model suggests that coagulation during the experiments may be sufficient to significantly remove the particles for the suspension by sedimentation or reduce the total particle surface area available for ice nucleation to take place. Aggregation was confirmed to take place in mineral suspensions using dynamic light-scattering measurements. However, it is not proven that aggregation of the mineral particles is able to reduce the surface area available for ice nucleation. The implication is that the mineral particles may be more important at nucleating ice at high temperatures than previously thought.
Sea salt aerosols as a reactive surface for inorganic and organic acidic gases in the Arctic troposphere

Sea salt aerosols (SSA) are dominant particles in the Arctic atmosphere and determine the polar radiative balance. SSA react with acidic pollutants that lead to changes in physical and chemical properties of their surface, which in turn alter their hygroscopic and optical properties. Transmission electron microscopy with energy-dispersive X-ray spectrometry was used to analyze morphology, composition, size, and mixing state of individual SSA at Ny-Ålesund, Svalbard, in summertime. Individual fresh SSA contained cubic NaCl coated by certain amounts of MgCl2 and CaSO4. Individual partially aged SSA contained irregular NaCl coated by a mixture of NaNO3, Na2SO4, Mg(NO3)2, and MgSO4. The comparison suggests the hydrophilic MgCl2 coating in fresh SSA likely intrigued the heterogeneous reactions at the beginning of SSA and acidic gases. Individual fully aged SSA normally had Na2SO4 cores and an amorphous coating of NaNO3. Elemental mappings of individual SSA particles revealed that as the particles ageing Cl gradually decreased, the C, N, O, and S content increased. 12C- mapping from nanoscale secondary ion mass spectrometry indicates that organic matter increased in the aged SSA compared with the fresh SSA. 12C- line scan further shows that organic matter was mainly concentrated on the aged SSA surface. These new findings indicate that this mixture of organic matter and NaNO3 on particle surfaces likely determines their hygroscopic and optical properties. These abundant SSA as reactive surfaces adsorbing inorganic and organic acidic gases can shorten acidic gas lifetime and influence the possible gaseous reactions in the Arctic atmosphere, which need to be incorporated into atmospheric chemical models in the Arctic troposphere.
Sources and chemical characterization of organic aerosol during the summer in the eastern Mediterranean

The concentration and chemical composition of non-refractory fine particulate matter (NR-PM1) and black carbon (BC) levels were measured during the summer of 2012 in the suburbs of two Greek cities, Patras and Athens, in an effort to better understand the chemical processing of particles in the high photochemical activity environment of the eastern Mediterranean. The composition of PM1 was surprisingly similar in both areas, demonstrating the importance of regional sources for the corresponding pollution levels. The PM1 average mass concentration was 9–14 μg m−3. The contribution of sulfate was around 38 %, while organic aerosol (OA) contributed approximately 45 % in both cases. PM1 nitrate levels were low (2 %). The oxygen to carbon (O : C) atomic ratio was 0.50 ± 0.08 in Patras and 0.47 ± 0.11 in Athens. In both cases PM1 was acidic. Positive matrix factorization (PMF) was applied to the high-resolution organic aerosol mass spectra obtained by an Aerodyne High-Resolution Time-of-Flight Aerosol Mass Spectrometer (HR-ToF-AMS). For Patras, five OA sources could be identified: 19 % very oxygenated OA (V-OOA), 38 % moderately oxygenated OA (M-OOA), 21 % biogenic oxygenated OA (b-OOA), 7 % hydrocarbon-like OA (HOA-1) associated with traffic sources and 15 % hydrocarbon-like OA (HOA-2) related to other primary emissions (including cooking OA). For Athens, the corresponding source contributions were: V-OOA (35 %), M-OOA (30 %), HOA-1 (18 %) and HOA-2 (17 %). In both cities the major component was OOA, suggesting that under high photochemical conditions most of the OA in the eastern Mediterranean is quite aged. The contribution of the primary sources (HOA-1 and HOA-2) was important (22 % in Patras and 35 % in Athens) but not dominant.
Fourteen months of on-line measurements of the non-refractory submicron aerosol at the Jungfraujoch (3580 m a.s.l.) – chemical composition, origins and organic aerosol sources

Chemically resolved (organic, nitrate, sulfate, ammonium) data of non-refractory submicron (NR-PM1) aerosol from the first long-term deployment (27 July 2012 to 02 October 2013) of a time-of-flight aerosol chemical speciation monitor (ToF-ACSM) at the Swiss high-altitude site Jungfraujoch (JFJ; 3580 m a.s.l.) are presented. Besides total mass loadings, diurnal variations and relative species contributions during the different meteorological seasons, geographical origin and sources of organic aerosol (OA) are discussed. Backward transport simulations show that the highest (especially sulfate) concentrations of NR-PM1 were measured in air masses advected to the station from regions south of the JFJ, while lowest concentrations were seen from western regions. OA source apportionment for each season was performed using the Source Finder (SoFi) interface for the multilinear engine (ME-2). OA was dominated in all seasons by oxygenated OA (OOA, 71–88 %), with lesser contributions from local tourism-related activities (7–12 %) and hydrocarbon-like OA related to regional vertical transport (3–9 %). In summer the OOA can be separated into a background low-volatility OA (LV-OOA I, possibly associated with long-range transport) and a slightly less oxidised low-volatility OA (LV-OOA II) associated with regional vertical transport. Wood burning-related OA associated with regional transport was detected during the whole winter 2012/2013 and during rare events in summer 2013, in the latter case attributed to small-scale transport for the surrounding valleys. Additionally, the data were divided into periods with free tropospheric (FT) conditions and periods with planetary boundary layer (PBL) influence, enabling the assessment of the composition for each. Most nitrate and part of the OA are injected from the regional PBL, while sulfate is mainly produced in the FT. The south/north gradient of sulfate is also pronounced in FT air masses (sulfate mass fraction from the south: 45 %; from the north: 29 %). Furthermore, a detailed investigation of specific marker fragments of the OA spectra (f43, f44, f55, f57, f60) showed different degrees of ageing depending on season.
HTAP_v2.2: a mosaic of regional and global emission grid maps for 2008 and 2010 to study hemispheric transport of air pollution

The mandate of the Task Force Hemispheric Transport of Air Pollution (TF HTAP) under the Convention on Long-Range Transboundary Air Pollution (CLRTAP) is to improve the scientific understanding of the intercontinental air pollution transport, to quantify impacts on human health, vegetation and climate, to identify emission mitigation options across the regions of the Northern Hemisphere, and to guide future policies on these aspects. The harmonization and improvement of regional emission inventories is imperative to obtain consolidated estimates on the formation of global-scale air pollution. An emissions data set has been constructed using regional emission grid maps (annual and monthly) for SO2, NOx, CO, NMVOC, NH3, PM10, PM2.5, BC and OC for the years 2008 and 2010, with the purpose of providing consistent information to global and regional scale modelling efforts. This compilation of different regional gridded inventories – including that of the Environmental Protection Agency (EPA) for USA, the EPA and Environment Canada (for Canada), the European Monitoring and Evaluation Programme (EMEP) and Netherlands Organisation for Applied Scientific Research (TNO) for Europe, and the Model Inter-comparison Study for Asia (MICS-Asia III) for China, India and other Asian countries – was gap-filled with the emission grid maps of the Emissions Database for Global Atmospheric Research (EDGARv4.3) for the rest of the world (mainly South America, Africa, Russia and Oceania). Emissions from seven main categories of human activities (power, industry, residential, agriculture, ground transport, aviation and shipping) were estimated and spatially distributed on a common grid of 0.1° × 0.1° longitude-latitude, to yield monthly, global, sector-specific grid maps for each substance and year. The HTAP_v2.2 air pollutant grid maps are considered to combine latest available regional information within a complete global data set. The disaggregation by sectors, high spatial and temporal resolution and detailed information on the data sources and references used will provide the user the required transparency. Because HTAP_v2.2 contains primarily official and/or widely used regional emission grid maps, it can be recommended as a global baseline emission inventory, which is regionally accepted as a reference and from which different scenarios assessing emission reduction policies at a global scale could start. An analysis of country-specific implied emission factors shows a large difference between industrialised countries and developing countries for acidifying gaseous air pollutant emissions (SO2 and NOx) from the energy and industry sectors. This is not observed for the particulate matter emissions (PM10, PM2.5), which show large differences between countries in the residential sector instead. The per capita emissions of all world countries, classified from low to high income, reveal an increase in level and in variation for gaseous acidifying pollutants, but not for aerosols. For aerosols, an opposite trend is apparent with higher per capita emissions of particulate matter for low income countries.
Natural new particle formation at the coastal Antarctic site Neumayer

We measured condensation particle (CP) concentrations and particle size distributions at the coastal Antarctic station Neumayer (70°39´ S, 8°15´ W) during two summer campaigns (from 20 January to 26 March 2012 and 1 February to 30 April 2014) and during the polar night between 12 August and 27 September 2014 in the particle diameter (Dp) range from 2.94 to 60.4 nm (2012) and from 6.26 to 212.9 nm (2014). During both summer campaigns we identified all in all 44 new particle formation (NPF) events. From 10 NPF events, particle growth rates could be determined to be around 0.90 ± 0.46 nm h−1 (mean ± SD; range: 0.4–1.9 nm h−1). With the exception of one case, particle growth was generally restricted to the nucleation mode (Dp < 25 nm) and the duration of NPF events was typically around 6.0 ± 1.5 h (mean ± SD; range: 4–9 h). Thus, in the surrounding area of Neumayer, particles did not grow up to sizes required for acting as cloud condensation nuclei. NPF during summer usually occurred in the afternoon in coherence with local photochemistry. During winter, two NPF events could be detected, though showing no ascertainable particle growth. A simple estimation indicated that apart from sulfuric acid, the derived growth rates required other low volatile precursor vapours.
The MCM v3.3.1 degradation scheme for isoprene

The chemistry of isoprene degradation in the Master Chemical Mechanism (MCM) has been systematically refined and updated to reflect recent advances in understanding, with these updates appearing in the latest version, MCM v3.3.1. The complete isoprene degradation mechanism in MCM v3.3.1 consists of 1926 reactions of 602 closed shell and free radical species, which treat the chemistry initiated by reaction with OH radicals, NO3 radicals and ozone (O3). A detailed overview of the updates is provided, within the context of reported kinetic and mechanistic information. The revisions mainly relate to the OH-initiated chemistry, which tends to dominate under atmospheric conditions, although these include updates to the chemistry of some products that are also generated from the O3- and NO3-initiated oxidation. The revisions have impacts in a number of key areas, including HOx recycling, NOx recycling and the formation of species reported to play a role in SOA (secondary organic aerosol)-formation mechanisms. The performance of the MCM v3.3.1 isoprene mechanism has been compared with those of earlier versions (MCM v3.1 and MCM v3.2) over a range of relevant conditions, using a box model of the tropical forested boundary layer. The results of these calculations are presented and discussed and are used to illustrate the impacts of the mechanistic updates in MCM v3.3.1.
The impacts of volcanic aerosol on stratospheric ozone and the Northern Hemisphere polar vortex: separating radiative-dynamical changes from direct effects due to enhanced aerosol heterogeneous chemistry

After major volcanic eruptions the enhanced aerosol causes ozone changes due to greater heterogeneous chemistry on the particle surfaces (HET-AER) and from dynamical effects related to the radiative heating of the lower stratosphere (RAD-DYN). We carry out a series of experiments with an atmosphere–ocean–chemistry–climate model to assess how these two processes change stratospheric ozone and Northern Hemispheric (NH) polar vortex dynamics. Ensemble simulations are performed under present day and preindustrial conditions, and with aerosol forcings representative of different eruption strength, to investigate changes in the response behaviour. We show that the halogen component of the HET-AER effect dominates under present-day conditions with a global reduction of ozone (−21 DU for the strongest eruption) particularly at high latitudes, whereas the HET-AER effect increases stratospheric ozone due to N2O5 hydrolysis in a preindustrial atmosphere (maximum anomalies +4 DU). The halogen-induced ozone changes in the present-day atmosphere offset part of the strengthening of the NH polar vortex during mid-winter (reduction of up to −16 m s-1 in January) and slightly amplify the dynamical changes in the polar stratosphere in late winter (+11 m s-1 in March). The RAD-DYN mechanism leads to positive column ozone anomalies which are reduced in a present-day atmosphere by amplified polar ozone depletion (maximum anomalies +12 and +18 DU for present day and preindustrial, respectively). For preindustrial conditions, the ozone response is consequently dominated by RAD-DYN processes, while under present-day conditions, HET-AER effects dominate. The dynamical response of the stratosphere is dominated by the RAD-DYN mechanism showing an intensification of the NH polar vortex in winter (up to +10 m s-1 in January). Ozone changes due to the RAD-DYN mechanism slightly reduce the response of the polar vortex after the eruption under present-day conditions.